Automation Presses Tooling

Generally you can differentiate the supply chain or supply network of Automation Presses Tooling by two perspectives:

• The supplier side (a so-called Tier-1-supplier is a direct supplier, Tier-2 is a supplier of the Tier-1 supplier, Tier-n is a supplier at any level in the Automation Presses Tooling supply network).
• The buyer side (a so-called Tier-1 buyer is a direct buyer, Tier-2 is a buyer of the Tier-1 buyer, Tier-n is a buyer at any level in the Automation Presses Tooling distribution network).

To ensure business stability and continuity, a supply chain or supply network must be constructed in such a way that external influences can cause as little damage as possible to Automation Presses Tooling. This applies both in the area of procurement (the loss of a supplier must be covered by an alternative supplier) as in the area of sales (the loss of a buyer must be covered by an alternative buyer).

Risks can generally be considered as the non-availability of goods, through cutback or complete halt of production, or the potential loss of business partners, violating compliance rules (e.g. protection of the environment, labor legislation) and thus drop out of the supply network.

This risk should not necessarily be limited to the direct business partner (Tier 1), it involves the entire supply chain, unless sufficient alternative suppliers and buyers have been put in place.

Get an overview of the international supply chain of Automation Presses Tooling (upstream/procurement and downstream/sales) from Tier-1 to Tier-n

ABRAMS world trade wiki not only shows direct suppliers and customers of the first tier (Tier-1). With just one click in our tool Supply Chain Intelligence you get a comprehensive insight into the supply network with multiple tiers (Tier-n) beyond the first tier.

Each tier in the supply chain or supply network on the supplier side of Automation Presses Tooling involves a single risk. The more tiers, the more difficult it is to analyze and monitor the business partners. Suppliers of suppliers are generally unknown, so there is already an increasing risk at the second (Tier 2) level.

If e.g. a first Tier supplier is not adding any value, the supply chain can be shortened and the risk of failure can be minimized by skipping this supplier. A previous Tier-2 supplier now turns into a Tier-1 supplier, which we call "go-direct". In our tool Supply Chain Intelligence as far as international suppliers are concerned, this analysis can be done with one click:

Analyze the potential of shortening and therefore stabilizing the supply chain of Automation Presses Tooling

Based on the analysis of international bills of lading (bill of lading/bills of lading / BOL), 1 product category that has been purchased by Automation Presses Tooling can be identified by means of HS codes (HTS codes or customs tariff numbers).

It is classified with the HS code 850433, which groups following products:

„Transformers having a power handling capacity > 16 kVA but <= 500 kVA (excl. liquid dielectric transformers)". This HS code was sighted 1 time in total.

Get an overview of internationally purchased products by Automation Presses Tooling with Company Transparency

Based on the analysis of international bills of lading (bill of lading/ bills of lading/ BOL), a total of 3 different product categories sold by Automation Presses Tooling, can be identified.

These are classified by means of HS codes (HTS codes or customs tariff numbers).

For example, HS code 340399 classifies the following products:

„Lubricant preparations, incl. cutting-oil preparations, bolt or nut release preparations, anti-rust or anti-corrosion preparations and mould-release preparations, based on lubricants but not containing petroleum oil or bituminous mineral oil (excl. preparations for the treatment of textiles, leather, furskins and other materials)". This HS code was sighted 1 time in total.

Get an overview of internationally sold products by Automation Presses Tooling with Company Transparency

Each company contributes significantly minimizing risks for its buyers, through its own stability. Internal risks (endogenous factors) can be e.g. financially (financial ratios, free cash flow, balance sheets) or operationally (production, lead times). Since 2021, external risks have increased due to worldwide shortages and are an important factor as to whether a supplier such as Automation Presses Tooling can itself reliably deliver due to external dependencies (exogenous factors).

To assess this, data analysis should be conducted to get practical answers:

Generally you can differentiate the competition of Automation Presses Tooling by the purchase and sales perspective.

• Start the competitive analysis on the purchase side.
• Start the competitive analysis on the sales side.

Competitors of Automation Presses Tooling on the purchase side (procurement of raw materials and components for production or distribution) are exposed on ABRAMs wiki under Competitive Intelligence, purchased products, classified by HS-Codes (e.g. 850433) or by top product terms.

Competitors on the sales side of Automation Presses Tooling (selling raw materials or components for production or distribution) are exposed on ABRAMS wiki under Competitive Intelligence, sold products classified by HS-Codes (e.g. 340399, 392330) or by top product terms.